Much closer to the 4WD 4L80E swap!
#1
TECH Fanatic
Thread Starter
iTrader: (2)
Join Date: Aug 2003
Location: Portland, OR
Posts: 1,068
Likes: 0
Received 0 Likes
on
0 Posts
Much closer to the 4WD 4L80E swap!
After searching the numerous posts on this subject and not finding any firm answers, I finally jumped under the truck and opened up my Helms manual to try get things straight.
My 2000 Helms only lists 2 Transfer cases; the Two speed Automatic (NP8) and Two Speed Manual, so I figured these things had to be interchangable among the motors. Well low and behold, my 1500's NVG-NP8 behind the 4L60E also fits behind the 4L80E! There are different length adapters to compensate for the difference in transmission lengths. This may very well be old news, but I'm stoked since I don't need to worry about custom transfer case wiring and such. Now what is that damn adapter's P/N?
I hope this helps out the fellow 4WD guys. Too bad There are no answeres to the SS's AWD dilema.
My 2000 Helms only lists 2 Transfer cases; the Two speed Automatic (NP8) and Two Speed Manual, so I figured these things had to be interchangable among the motors. Well low and behold, my 1500's NVG-NP8 behind the 4L60E also fits behind the 4L80E! There are different length adapters to compensate for the difference in transmission lengths. This may very well be old news, but I'm stoked since I don't need to worry about custom transfer case wiring and such. Now what is that damn adapter's P/N?
I hope this helps out the fellow 4WD guys. Too bad There are no answeres to the SS's AWD dilema.
#3
TECH Fanatic
Thread Starter
iTrader: (2)
Join Date: Aug 2003
Location: Portland, OR
Posts: 1,068
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Wilde Racing
All you got to do is swap out this input shaftsun gear and it will bolt right up.
#6
Staging Lane
Join Date: Jun 2004
Location: Formerly Hayden, AL . . . Now Attleboro Falls, MA
Posts: 87
Likes: 0
Received 0 Likes
on
0 Posts
Wow! That looks like you had to take the t-case completely apart to swap out that gear. How hard was it to do? What sorts of special tools, etc. were required?
#7
How do I change this text
iTrader: (26)
Join Date: Jan 2005
Location: Behind the TIG welder
Posts: 7,294
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by ecthelion
Wow! That looks like you had to take the t-case completely apart to swap out that gear. How hard was it to do? What sorts of special tools, etc. were required?
I can't find the paper with the part # of the input shaft, I will keep looking.
Trending Topics
#9
FormerVendor
iTrader: (1)
Originally Posted by Wilde Racing
A good pair of snap ring pliers is about it.
I can't find the paper with the part # of the input shaft, I will keep looking.
I can't find the paper with the part # of the input shaft, I will keep looking.
Chuck
#10
How do I change this text
iTrader: (26)
Join Date: Jan 2005
Location: Behind the TIG welder
Posts: 7,294
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by 4.8T
so did you have to change the drive shaft or not since you were 4wd and use your stock t-case
Does the part number- 19019 Ring a bell for the input shaft, FLT? I found my invoice but I don't think this is the right number.