First time ever on a dyno
06-06-2011, 04:24 PM
#1
First time ever on a dyno
There was a "dyno day" in Anchorage on Saturday, so I decided to do it. Anyways, made 3 pulls, here's the vids. He doesn't have a printer, so he's going to e-mail me the graphs. I don't have them yet, but I'll post them up after I get them. IIRC, it made 425rwhp/428rwtq. I need a smaller pulley & bigger injectors....
All in all, it was a pretty fun day.
First pull was in 2nd gear. Check out how the Cal-Tracs lift the rear of the truck.
http://www.youtube.com/watch?v=lTVw5047koI
Second & third pulls were in 3rd gear.
http://www.youtube.com/watch?v=8y-Wd...eature=related
http://www.youtube.com/watch?v=WLkJK...eature=related
All in all, it was a pretty fun day.First pull was in 2nd gear. Check out how the Cal-Tracs lift the rear of the truck.
http://www.youtube.com/watch?v=lTVw5047koI
Second & third pulls were in 3rd gear.
http://www.youtube.com/watch?v=8y-Wd...eature=related
http://www.youtube.com/watch?v=WLkJK...eature=related
06-06-2011, 04:37 PM
#2
Where do i start,
The truck looks awesome, so damn clean , specially for the beautiful weather you have up there!
Good numbers bud, Id say they are pretty damn stout, specially with the ET's you run.
Sounds damn good too.
Very cool how the truck wanted to launch when the hammer was down!
So did you do any tune tweaking while on the dyno??
Cool Deal Rodger, thanks for sharing, i enjoy these kind of vids.
The truck looks awesome, so damn clean , specially for the beautiful weather you have up there!
Good numbers bud, Id say they are pretty damn stout, specially with the ET's you run.
Sounds damn good too.
Very cool how the truck wanted to launch when the hammer was down!
So did you do any tune tweaking while on the dyno??
Cool Deal Rodger, thanks for sharing, i enjoy these kind of vids.
06-06-2011, 07:11 PM
#4
Apparently, my truck was the loudest vehicle of the day...
It was a "no tuning on the dyno" day, there were too many vehicles waiting. I added 5 gallons of Trick 114 to the tank that morning, to verify that my previous KR was caused by crappy fuel. There was no KR on the dyno, and my timing was at 16 degrees(WOT). I wanted to remove 8 degrees and run it again to measure power loss(as mentioned in my other thread), and then add some timing above 16 degrees also, but I couldn't.
They did offer to sell me some dyno time for tuning, on another day.
It was a "no tuning on the dyno" day, there were too many vehicles waiting. I added 5 gallons of Trick 114 to the tank that morning, to verify that my previous KR was caused by crappy fuel. There was no KR on the dyno, and my timing was at 16 degrees(WOT). I wanted to remove 8 degrees and run it again to measure power loss(as mentioned in my other thread), and then add some timing above 16 degrees also, but I couldn't.
They did offer to sell me some dyno time for tuning, on another day.
Trending Topics
06-06-2011, 10:00 PM
#8
TECH Enthusiast
iTrader: (13)
Join Date: Jul 2007
Location: South of South Ft Worth
Posts: 714
Likes: 0
Received 0 Likes
on
0 Posts
Damn one of the best lookin ex cabs ive seen. Nice pull once we get smaller pulley and tuned were gonna get some pulls in to see where werre at also. Identical setup as u. Jus few diff things
