compression ratio for new motor.
#12
Performance Trucks Sponsor
iTrader: (5)
Join Date: Jul 2002
Location: san antonio, tx
Posts: 1,439
Likes: 0
Received 0 Likes
on
0 Posts
I like to run springs only in my racetruck. I get tired of messing with controllers.
If I do use one, it's very simple. It's the cheap turbosmart controller that bleeds off the hose.
If I do use one, it's very simple. It's the cheap turbosmart controller that bleeds off the hose.
#16
TECH Senior Member
iTrader: (26)
I thought is was his tune and over boost that caused the failure?
That's why I always build FI tunes so if it over boost or get into a part of the table that isn't tuned for, it goes pig rich and pulls a ton of timing. I know my truck will instantly pull about 10* of timing if I go over 16psi, and my VE tables look like valleys with the tuned part being the bottoms and everything else is a far bit higher just in case something like what happened to him happens. I can't afford new motors every other week
That's why I always build FI tunes so if it over boost or get into a part of the table that isn't tuned for, it goes pig rich and pulls a ton of timing. I know my truck will instantly pull about 10* of timing if I go over 16psi, and my VE tables look like valleys with the tuned part being the bottoms and everything else is a far bit higher just in case something like what happened to him happens. I can't afford new motors every other week
#17
TECH Resident
Thread Starter
iTrader: (6)
Join Date: Sep 2005
Location: Benson NC
Posts: 856
Likes: 0
Received 0 Likes
on
0 Posts
I thought is was his tune and over boost that caused the failure?
it was. but i was trying to do some of the tuning my self. but ill let the 3 time record holder ryan do all of it this time...lol
That's why I always build FI tunes so if it over boost or get into a part of the table that isn't tuned for, it goes pig rich and pulls a ton of timing. I know my truck will instantly pull about 10* of timing if I go over 16psi, and my VE tables look like valleys with the tuned part being the bottoms and everything else is a far bit higher just in case something like what happened to him happens. I can't afford new motors every other week
it was. but i was trying to do some of the tuning my self. but ill let the 3 time record holder ryan do all of it this time...lol
That's why I always build FI tunes so if it over boost or get into a part of the table that isn't tuned for, it goes pig rich and pulls a ton of timing. I know my truck will instantly pull about 10* of timing if I go over 16psi, and my VE tables look like valleys with the tuned part being the bottoms and everything else is a far bit higher just in case something like what happened to him happens. I can't afford new motors every other week
#18
TECH Fanatic
iTrader: (26)
Join Date: Aug 2008
Location: Where our street cars are faster than your racecars..Mississippi
Posts: 1,113
Likes: 0
Received 0 Likes
on
0 Posts
mine is 9.25:1 TEXAS SPEED HIGHLY recommended me to run that set up with my 408ci and 88mm turbo for street/strip application for 750+ on pump gas and who knows on the meth..lol
#20
TECH Fanatic
iTrader: (26)
Join Date: Aug 2008
Location: Where our street cars are faster than your racecars..Mississippi
Posts: 1,113
Likes: 0
Received 0 Likes
on
0 Posts
lol... been caught up riding 4 wheelers lol
bought me a built motor'd can-am 800ish...lol now it is bein painted
i do need a few things:
cam
springs
studs
and a few small things
bought me a built motor'd can-am 800ish...lol now it is bein painted
i do need a few things:
cam
springs
studs
and a few small things