4l60e Rebuild List
#1
Staging Lane
Thread Starter
iTrader: (3)
Join Date: Jan 2009
Location: Cold Lake, Alberta
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
4l60e Rebuild List
I am going to rebuild my 4l60e soon and wanting to make sure i get everything i need. I made this list so far. Just wondering if there is anything that I am missing?
Corvette Servo kit
SONNAX 4TH GEAR BILLET SERVO
ALTO HP RED 3-4 CLUTCH POWERPACK
Beast Sun Gear Shell
13 Vane Pump kit
HD 5 Pinion Rear Planetary Gear Set
SONNAX 4L60E PINLESS FORWARD ACCUMULATOR
Alto Carbonite, Wide Carbon Band
TRANSGO HD2 SHIFT KIT
Sonnax Input Drum Reinforcement Kit
HD BORG WARNER 29 ELEMENT FORWARD SPRAG
BUSHING KIT
TORRINGTON BEARING KIT
Transtec Overhaul Gasket Set
Corvette Servo kit
SONNAX 4TH GEAR BILLET SERVO
ALTO HP RED 3-4 CLUTCH POWERPACK
Beast Sun Gear Shell
13 Vane Pump kit
HD 5 Pinion Rear Planetary Gear Set
SONNAX 4L60E PINLESS FORWARD ACCUMULATOR
Alto Carbonite, Wide Carbon Band
TRANSGO HD2 SHIFT KIT
Sonnax Input Drum Reinforcement Kit
HD BORG WARNER 29 ELEMENT FORWARD SPRAG
BUSHING KIT
TORRINGTON BEARING KIT
Transtec Overhaul Gasket Set
#4
TECH Fanatic
iTrader: (10)
Join Date: May 2007
Location: Fort Worth Texas
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
Good luck with the Alto power-pack.
A set of hardened pump rings is cheap insurance also.
A new spacer plate would be nice.
At bare minimum I would change the pressure control solenoid, if not all solenoids.
1-2 plastic accumulator piston needs to be tossed in favor of an aluminum also.
A set of hardened pump rings is cheap insurance also.
A new spacer plate would be nice.
At bare minimum I would change the pressure control solenoid, if not all solenoids.
1-2 plastic accumulator piston needs to be tossed in favor of an aluminum also.
#5
TECH Enthusiast
iTrader: (3)
Join Date: Dec 2009
Location: Pasadena, COnroe
Posts: 662
Likes: 0
Received 0 Likes
on
0 Posts
Get the double sprag.
On the 5 pinion planetarty, make sure its not a cheap imitation ones that are out there. look them up on my thread.
I would get a non cork gasket $7.
With the sonnax reinforcement ring, read the instructrions carefully.
heres my 60e build thread https://www.performancetrucks.net/fo...d.php?t=462047
One last recomendation, get a trans temp guage and 40k cooler.
On the 5 pinion planetarty, make sure its not a cheap imitation ones that are out there. look them up on my thread.
I would get a non cork gasket $7.
With the sonnax reinforcement ring, read the instructrions carefully.
heres my 60e build thread https://www.performancetrucks.net/fo...d.php?t=462047
One last recomendation, get a trans temp guage and 40k cooler.
#6
11 Second Hall Moniter
iTrader: (22)
Won't last long behind that TVS1900. You've chose the wrong 3-4 clutch pack, and the wrong band. IIRC, they each lasted about 6 weeks behind my MP112. In fact, I've yet to have ANY 4L65E last 12 months. I strongly recommend that you review this link, and make a phone call to them.
http://www.finishlinetrans.com/trans...rmance4L65.htm
http://www.finishlinetrans.com/trans...rmance4L65.htm
#7
TECH Enthusiast
iTrader: (3)
Join Date: Dec 2009
Location: Pasadena, COnroe
Posts: 662
Likes: 0
Received 0 Likes
on
0 Posts
At the end of my thread on my 60e build I did wish i had gone with a built 80e from a sponsor. I burnt up about $3k on that thread. I could have converted over to a built 80e. Ive been up since 6am monday and did not read your sig until the previous post. zzz