New Exhaust Pics and Vids!
03-27-2011 | 01:04 PM
#51
Well if I was outside trying to figure out how to work my camcorder, how could I have answered your PM so expeditiously? 
Kinda glad that I stayed in now huh? 
I'm not worried about me melting, but H2O and electronics don't mix very well...I would like to use this camcorder more than once ya know
And what are you worried about? You already have your kickazz Corsa
Kinda glad that I stayed in now huh? I'm not worried about me melting, but H2O and electronics don't mix very well...I would like to use this camcorder more than once ya know
And what are you worried about? You already have your kickazz Corsa
Ya, ecstatic.
You did say u didn't wanna get wet earlier, no mention of electronics.
Oh ya, I do.
Thanks for kind words, tho you've never heard my setup.Idle & rev vid, not a bad 1st vid.
"sounds like it's time for a bigger cam
Yea, or a bigger engine 
As for your making motorboat sounds with your mouth, John mentioned that to somebody on here.
03-27-2011 | 02:44 PM
#53
04-03-2011 | 02:55 PM
#57
Thread Starter
PT's Slowest Truck
iTrader: (19)
Joined: Apr 2004
Posts: 17,863
Likes: 2
From: Hackensack, NJ
OK, I'm bummed 
I wired in the DMH E-cutout yesterday, and the darn thing doesn't work 
I have power and ground to the motor with the switch in both directions, and when I removed the cutout and bench tested it's a no-go. I hear the motor clicking and trying to do something but the butterfly doesn't even budge. So I guess that I'll have to contact DMH tomorrow and send this thing back to them, I bought it about a year ago and just installed it a week or two ago. Hopefully I'll get it back quickly as I'm totally psyched to use this thing 
I wired in the DMH E-cutout yesterday, and the darn thing doesn't work I have power and ground to the motor with the switch in both directions, and when I removed the cutout and bench tested it's a no-go. I hear the motor clicking and trying to do something but the butterfly doesn't even budge. So I guess that I'll have to contact DMH tomorrow and send this thing back to them, I bought it about a year ago and just installed it a week or two ago. Hopefully I'll get it back quickly as I'm totally psyched to use this thing
04-03-2011 | 07:18 PM
#58
Damn, that sucks.
I had one on my car. It didn't make any difference whatsoever, lol, but it sure sounded good...
Closed cutout:
http://www.youtube.com/watch?v=hFgzLu59a5Q
Open cutout:
http://www.youtube.com/watch?v=adh4BnfBMBg
I had one on my car. It didn't make any difference whatsoever, lol, but it sure sounded good...
Closed cutout:http://www.youtube.com/watch?v=hFgzLu59a5Q
Open cutout:http://www.youtube.com/watch?v=adh4BnfBMBg
04-04-2011 | 12:48 AM
#59
Thread Starter
PT's Slowest Truck
iTrader: (19)
Joined: Apr 2004
Posts: 17,863
Likes: 2
From: Hackensack, NJ
Yea it seems like some guys gain a tenth or two, but most don't see any gains...honestly, I got it as more of a toy to mess with people at stop lights, and for when I go up to the Summer Nats in Massachusetts where just about everyone is running around with open cutouts
04-04-2011 | 09:33 AM
#60
My favorite cutout "use" was to blast the earwax out of those pesky little fart piped car drivers, LOL. As idling up beside them, a quick flip of the switch and a converter that flashed to 4200 made sure they were paying attention, LMAO!
That bottom video was at a Mustang track rental and evidently they don't speak "cutout" because quite a few wondered (and asked) how my car was so quiet in the burnout area, and driving through the pits, but so damn loud when launching/racing.
That bottom video was at a Mustang track rental and evidently they don't speak "cutout" because quite a few wondered (and asked) how my car was so quiet in the burnout area, and driving through the pits, but so damn loud when launching/racing.