aluminum driveshaft
09-20-2009, 02:38 PM
#1
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Feb 2003
Location: pensacola fl
Posts: 3,048
Likes: 0
Received 0 Likes
on
0 Posts
aluminum driveshaft
gm 15165400
removed from 2002 ext cab, short bed
its the big forged spicer yoke on the end. not sure if its for the 4l80 or it goes into the transfer case for a 4wd. they may be the same spline? could easily be swapped out.
use the tube and shorten it, or buy it for the yoke.
this yoke is 150+ bucks new.
driveshaft measures 68" center of u joint to center of u joint.
driveshaft priced from gm is just over 450 bucks.
50.00+actual shipping
removed from 2002 ext cab, short bed
its the big forged spicer yoke on the end. not sure if its for the 4l80 or it goes into the transfer case for a 4wd. they may be the same spline? could easily be swapped out.
use the tube and shorten it, or buy it for the yoke.
this yoke is 150+ bucks new.
driveshaft measures 68" center of u joint to center of u joint.
driveshaft priced from gm is just over 450 bucks.
50.00+actual shipping
09-21-2009, 10:14 AM
#2
TECH Fanatic
iTrader: (25)
Join Date: Nov 2001
Location: SC
Posts: 1,779
Likes: 0
Received 0 Likes
on
0 Posts
Can you measure the OD of the yoke and count the splines for me? I need this for a 4l80, ie needs 32 splines.
if it measure what I need I will purchase it, can you get me a shipped amt to 29682 (residintial) or 29631 (commercial)
if it measure what I need I will purchase it, can you get me a shipped amt to 29682 (residintial) or 29631 (commercial)
09-21-2009, 06:21 PM
#3
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Feb 2003
Location: pensacola fl
Posts: 3,048
Likes: 0
Received 0 Likes
on
0 Posts
i do not have the shaft in my possession.
i will be at the shop tomorrow and will get a measurement.
it may be tomorrow night before i get back with you.
thanks.
i will be at the shop tomorrow and will get a measurement.
it may be tomorrow night before i get back with you.
thanks.
09-23-2009, 08:33 PM
#4
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Feb 2003
Location: pensacola fl
Posts: 3,048
Likes: 0
Received 0 Likes
on
0 Posts
i had a huge brain fart and did not count the splines.
the driveshaft is 4" OD.
the spicer # on the yoke is C3-3329-6
it is 8" from tip to center of u joint.
6" for slip portion only.
1 3/4 OD
1 1/2 ID
(measured with a tape measure.)
i called my buddy at the dealer and he said that the part# had been replaced by 15751438 which is the same shaft with an upgraded u joint.
guess there is/was a TSB out on it. the part # fits 99-03 ext cab 4x4 short bed.
not sure if the yoke for the 4x4 is correct for the 4l80.
i will be back out at the shop tomorrow and count the splines if i cant get a good answer out a dana/spicer tomorrow.
i didnt get off work in time today to call spicer, but i cant find ANYTHING online about the yoke.
at least i narrowed it down that its for a 4wd.
the driveshaft is 4" OD.
the spicer # on the yoke is C3-3329-6
it is 8" from tip to center of u joint.
6" for slip portion only.
1 3/4 OD
1 1/2 ID
(measured with a tape measure.)
i called my buddy at the dealer and he said that the part# had been replaced by 15751438 which is the same shaft with an upgraded u joint.
guess there is/was a TSB out on it. the part # fits 99-03 ext cab 4x4 short bed.
not sure if the yoke for the 4x4 is correct for the 4l80.
i will be back out at the shop tomorrow and count the splines if i cant get a good answer out a dana/spicer tomorrow.
i didnt get off work in time today to call spicer, but i cant find ANYTHING online about the yoke.
at least i narrowed it down that its for a 4wd.
09-28-2009, 10:57 PM
#6
Staging Lane
iTrader: (83)
Join Date: Jul 2006
Location: Pensacola, FL
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
How long is the drive shaft? Could it be used with T-56 yoke & 8.5" 10 bolt? Would like to use this in my 69 camaro.
Scott
grsdup1@aol.com
Scott
grsdup1@aol.com
09-29-2009, 09:47 PM
#7
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Feb 2003
Location: pensacola fl
Posts: 3,048
Likes: 0
Received 0 Likes
on
0 Posts
you could use the tube with the proper front yoke. this one will not fit a t56. if you are hunting one, all th200, th350, 700r4, 4l60 use the same spline as the t56 unit.
its 4" in diameter. if you can fit that large of a shaft i dont see why you couldnt use it.
it will need to be shortened.
with a 6 spd, id guess your driveshaft will need to be somewhere in the mid/high 40" length with a 8.5 10 bolt out back.
its 4" in diameter. if you can fit that large of a shaft i dont see why you couldnt use it.
it will need to be shortened.
with a 6 spd, id guess your driveshaft will need to be somewhere in the mid/high 40" length with a 8.5 10 bolt out back.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
jscherbs
GM Parts Classifieds
3
09-30-2015 07:54 AM
BigKID
TOOLS & FABRICATION
0
09-22-2015 09:59 PM
