Built LQ4 short block, edelbrock 245s, 4l80e, nitrous and more
03-12-2010, 03:25 AM
#1
formerly silverbrick (changed 02/17/2013)
Thread Starter
iTrader: (5)
Join Date: Mar 2006
Location: Pasadena, Tx
Posts: 4,525
Likes: 0
Received 0 Likes
on
0 Posts
edelbrock 245s, 4l80e, nitrous, engine parts and more
Howdy Fellas, long no see on these boards. I am about to graduate from Texas A&M and some of my priorities have changed so I am looking to get rid of some of the parts I have stockpiled for a KILLER 370ci forged, nitrous motor. here is what I have--
*keep in mind I would prefer to sell this in some sort of package but I am more than willing to part it out if a few of yall decide you want some parts.*
Nick Williams 90mm cable throttle body, new in Box. Retails 419.95.....SOLD
Edelbrock Vic. Jr intake, plumbed with nitrous spray bars, AN fuel fittings and more New in Box. Kind of goes with the nitrous system.....SOLD
built 4l80e transmission. been dry stored for 2 years not sure what year it is, 2003 I think. Very low miles built to handle heavy duty use/horsepower....SOLD
2001 6.0litre LQ4 iron block short block. Completely re-machined and overbored to 4.030" (370ci). Bored, honed, decked, check for microscopic cracks, etc. Loaded with forged Mahle pistons with -2cc valve reliefs and forged Mahle rods. ARP bolts on all mains and rod bolts. New gaskets, front and rear covers, competition solid roller lifters, new bearings, oil pan, etc. comepletely assembled..... SOLD
2 Cometic 4.030" custom head gaskets. Brand New, reusable. Excellent quality. SOLD
Nitro daves custom sheet metal Intake Elbow....$225.00
Nitro Daves custom plate kit without plate (used to connect to spray bars in Vic Jr intake.). Up to 300hp supported. Comes with solenoids, AN fittings, tubing, 10# tank AND MORE new in box. $475.00
Morel Solid Roller Lifter Set-- part# 184-4737-SR.....$400 (retails at Thunder Racing for $495.00)
Customs cam from West Coast Cylinder Heads- solid roller- 252/258 .641 .652 110LSA.....$325
Hardened push rods length matched to cam and solid roller lifter combination....$75
WCCH customs machines Edelbrock 245 aluminum heads. Complete with patriot dual extreme (upgraded) springs and Harland Sharp 1.7 ratio adjustable rockets for a 12.1 compression ratio with the short block above (ARP headbolts included)....$2700.......$2350 w/o rockers
*** I will separate the Harland Sharp Adj. Stud mounted rockers from the heads if someone wants them. They list at Summit for $495 so I would do $425 shipped.
Keep in mind that even the parts that are not new in box have never been run and are in pristine condition. Most of them have just come out of the machine shop. The motor was being stored in my garage assembled as a long block. The intake components, and nitrous system are in boxes in the house. All prices are OR BEST OFFER. Things do not necessarily need to be sold but if you have a reasonable offer, shoot me a message or email.
Pictures are in 2 posts below.
*keep in mind I would prefer to sell this in some sort of package but I am more than willing to part it out if a few of yall decide you want some parts.*
Nick Williams 90mm cable throttle body, new in Box. Retails 419.95.....SOLD
Edelbrock Vic. Jr intake, plumbed with nitrous spray bars, AN fuel fittings and more New in Box. Kind of goes with the nitrous system.....SOLD
built 4l80e transmission. been dry stored for 2 years not sure what year it is, 2003 I think. Very low miles built to handle heavy duty use/horsepower....SOLD
2001 6.0litre LQ4 iron block short block. Completely re-machined and overbored to 4.030" (370ci). Bored, honed, decked, check for microscopic cracks, etc. Loaded with forged Mahle pistons with -2cc valve reliefs and forged Mahle rods. ARP bolts on all mains and rod bolts. New gaskets, front and rear covers, competition solid roller lifters, new bearings, oil pan, etc. comepletely assembled..... SOLD
2 Cometic 4.030" custom head gaskets. Brand New, reusable. Excellent quality. SOLD
Nitro daves custom sheet metal Intake Elbow....$225.00
Nitro Daves custom plate kit without plate (used to connect to spray bars in Vic Jr intake.). Up to 300hp supported. Comes with solenoids, AN fittings, tubing, 10# tank AND MORE new in box. $475.00
Morel Solid Roller Lifter Set-- part# 184-4737-SR.....$400 (retails at Thunder Racing for $495.00)
Customs cam from West Coast Cylinder Heads- solid roller- 252/258 .641 .652 110LSA.....$325
Hardened push rods length matched to cam and solid roller lifter combination....$75
WCCH customs machines Edelbrock 245 aluminum heads. Complete with patriot dual extreme (upgraded) springs and Harland Sharp 1.7 ratio adjustable rockets for a 12.1 compression ratio with the short block above (ARP headbolts included)....$2700.......$2350 w/o rockers
*** I will separate the Harland Sharp Adj. Stud mounted rockers from the heads if someone wants them. They list at Summit for $495 so I would do $425 shipped.
Keep in mind that even the parts that are not new in box have never been run and are in pristine condition. Most of them have just come out of the machine shop. The motor was being stored in my garage assembled as a long block. The intake components, and nitrous system are in boxes in the house. All prices are OR BEST OFFER. Things do not necessarily need to be sold but if you have a reasonable offer, shoot me a message or email.
Pictures are in 2 posts below.
Last edited by 1ImperialSS; 04-21-2010 at 08:53 PM. Reason: prices lowered
03-13-2010, 10:17 AM
#3
formerly silverbrick (changed 02/17/2013)
Thread Starter
iTrader: (5)
Join Date: Mar 2006
Location: Pasadena, Tx
Posts: 4,525
Likes: 0
Received 0 Likes
on
0 Posts
Yes it will but you will need a new flexplate which I also have, a new transmission wiring harness, and crossmember. It is 2wd. Pictures coming this evening of everything
03-13-2010, 12:29 PM
#4
TECH Enthusiast
iTrader: (12)
Join Date: Feb 2010
Location: warner robins, ga
Posts: 525
Likes: 0
Received 0 Likes
on
0 Posts
i have an engine harness already can jus swap the pcm wires around right? how much power can i handle,do u kno? an what does it have done to it makin it stronger?
03-13-2010, 06:11 PM
#6
formerly silverbrick (changed 02/17/2013)
Thread Starter
iTrader: (5)
Join Date: Mar 2006
Location: Pasadena, Tx
Posts: 4,525
Likes: 0
Received 0 Likes
on
0 Posts
No deals have gone down yet, I would also prefer to deal local so shoot me a PM so we can work something out. In the meantime, here are all the pictures of the motor and transmission. Pictures of the nitrous system, intake, Nick williams, etc that are NEW IN BOX will be uploaded later tonight or tomorrow but you can always see pictures of those online.
check out that porting!
check out that porting!
03-13-2010, 06:15 PM
#7
formerly silverbrick (changed 02/17/2013)
Thread Starter
iTrader: (5)
Join Date: Mar 2006
Location: Pasadena, Tx
Posts: 4,525
Likes: 0
Received 0 Likes
on
0 Posts
like I said, the long block in completely buttoned up so pictures of the cam, rods and pistons are not going to be available but all those parts were NIB and professionally installed.
Trending Topics
?
03-14-2010, 03:24 AM
#9
formerly silverbrick (changed 02/17/2013)
Thread Starter
iTrader: (5)
Join Date: Mar 2006
Location: Pasadena, Tx
Posts: 4,525
Likes: 0
Received 0 Likes
on
0 Posts
I would say the 4l80e could take 750-850 without too much trouble. It's a petty strong setup bone stock you know.