Forged 366 LS2 Stroker Motor Complete! $3500
#1
Staging Lane
Thread Starter
iTrader: (-1)
Join Date: Oct 2006
Location: Garner, NC
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Forged 366 LS2 Stroker Motor Complete! $3500
I have a complete LS2 engine from my 2003 AWD Escalade I'm selling. Has about 12,000 miles. Engine was built by Cartek in Garwood, NJ. Motor was built for a corvette to hold 20psi from forced induction, but I got it for a deal due to the original purchaser forfeiting their deposit. I have the original receipt where I paid the reduced price of $6680.00. The engine is built with the following:
Complete 366 Stroker includes, 3.622" stroke, 4340 callies crank, eagle 6.125 3D rods, Cartek/Diamond forged pistons, Balance assemble, Z06 oil pump, Nitrated double roller timing chain, custom cam shaft, High grade cam bolts, Plasma Molly ring set, Clevite H series race bearings, Cromoly push rods, Cartek Stage 3 ported heads, New valves, Titanium retainers, Race springs, Viton valve seals, Serdi "radiused" valve job, CBN milled .005, new head bolts, Hone with torque plate, all machine work, clean, blueprint, and assembly, Price is with core exchange.
I have upgraded the cam to a Lingenfelter GT2-3 cam which makes it idle better than stock, but gives it excellent power with boost. I had a paxton novi 1200 supercharger first, but then upgraded to the magnuson mp122 with 12 psi. Because the escalade was AWD, nobody could dyno the truck, but RPM in Garner, NC who did the tune estimated the HP to just over 500hp at the engine. The engine is capable of well over 800hp which enough for most folks. I'm selling the truck, and I won't get any extra if I kept everything installed. I'm giving this engine away for $3500 complete with all accessories attached to the block (A/C, alternator, etc), and putting a stock engine in its place. I will consider a trade in for your good working engine complete to replace this one. I have an upraded tranny for sale also, so please check my other posting.
Email me at staffcurtis@earthlink.net, or call at 919-796-9892 with any questions. I will put a video up shortly of the engine running with the supercharger. The supercharger is already sold.
Complete 366 Stroker includes, 3.622" stroke, 4340 callies crank, eagle 6.125 3D rods, Cartek/Diamond forged pistons, Balance assemble, Z06 oil pump, Nitrated double roller timing chain, custom cam shaft, High grade cam bolts, Plasma Molly ring set, Clevite H series race bearings, Cromoly push rods, Cartek Stage 3 ported heads, New valves, Titanium retainers, Race springs, Viton valve seals, Serdi "radiused" valve job, CBN milled .005, new head bolts, Hone with torque plate, all machine work, clean, blueprint, and assembly, Price is with core exchange.
I have upgraded the cam to a Lingenfelter GT2-3 cam which makes it idle better than stock, but gives it excellent power with boost. I had a paxton novi 1200 supercharger first, but then upgraded to the magnuson mp122 with 12 psi. Because the escalade was AWD, nobody could dyno the truck, but RPM in Garner, NC who did the tune estimated the HP to just over 500hp at the engine. The engine is capable of well over 800hp which enough for most folks. I'm selling the truck, and I won't get any extra if I kept everything installed. I'm giving this engine away for $3500 complete with all accessories attached to the block (A/C, alternator, etc), and putting a stock engine in its place. I will consider a trade in for your good working engine complete to replace this one. I have an upraded tranny for sale also, so please check my other posting.
Email me at staffcurtis@earthlink.net, or call at 919-796-9892 with any questions. I will put a video up shortly of the engine running with the supercharger. The supercharger is already sold.
Last edited by staffcurtis; 10-15-2008 at 11:14 AM.
#2
Staging Lane
Thread Starter
iTrader: (-1)
Join Date: Oct 2006
Location: Garner, NC
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Here is a video of the engine running I filmed about 2 weeks ago. The supercharger is being removed now. I had my wife rev the engine, but she didn't do it well (go figure).
Last edited by staffcurtis; 10-15-2008 at 11:46 AM.
Thread
Thread Starter
Forum
Replies
Last Post