Going with Greyghost4x4 tomorrow to Memphis for a dyno session......
01-15-2007, 09:35 AM
#61
TECH Senior Member
Thread Starter
iTrader: (9)
Join Date: Aug 2003
Location: Cleveland Mississippi
Posts: 6,204
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Joey5.4L
You sure you are not doing some internet sand bagging? I know that when I raced you at Greenville I didnt have spray, and my 60's where a lil slow with the DR's, but still, my old truck made 390hp and 480ft lbs on motor... And I am sure you haven't gotten slower over the past year. 
Maybe it weighs a whole lot less than I think it does. 
01-15-2007, 09:36 AM
#62
TECH Senior Member
Thread Starter
iTrader: (9)
Join Date: Aug 2003
Location: Cleveland Mississippi
Posts: 6,204
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by LilRick
Any vids??
01-15-2007, 09:48 AM
#63
TECH Enthusiast
iTrader: (1)
Join Date: Dec 2002
Location: Jackson, Mississippi
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by slowprocess
3rd gear pull converter locked numbers
360.76 hp 382.06 tq
Gas
445.38 hp 453.83 tq
Very disappointing but I like track dynos much better.
Max horsepower and torque was made around 5000rpms This thing is all over the place! I need to post up this dyno sheet for you guys........just to show you how bad the intake restricts high rpm power
360.76 hp 382.06 tq
Gas
445.38 hp 453.83 tq
Very disappointing but I like track dynos much better.
Max horsepower and torque was made around 5000rpms This thing is all over the place! I need to post up this dyno sheet for you guys........just to show you how bad the intake restricts high rpm power
01-15-2007, 01:42 PM
#64
TECH Senior Member
Thread Starter
iTrader: (9)
Join Date: Aug 2003
Location: Cleveland Mississippi
Posts: 6,204
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by blacksheep
You may have another problem because the stock intake is not that bad. My 6.0 w/ a 224/228 cam and half *** ported 317's made 417hp @6500 through an unlocked converter.
01-15-2007, 03:30 PM
#66
TECH Senior Member
Thread Starter
iTrader: (9)
Join Date: Aug 2003
Location: Cleveland Mississippi
Posts: 6,204
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by onebadrubi
Blacksheep care to share the dyno sheet if possible?
What about you slow?
What about you slow?
01-15-2007, 06:14 PM
#67
Launching!
Join Date: Feb 2006
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
im not so sure that their dyno is accurate, I was about 50 less than I was expecting. My truck dynoed before with 310 rwhp, yet it is 5400 lbs and ran the 1/4 mile in 14.2@95mph. That should be about 425-440 crank hp or around 350 rwhp. I wouldnt be surprised if it is off a little, like 40hp or so.
01-15-2007, 08:59 PM
#70
Banned
iTrader: (4)
Join Date: Oct 2003
Location: From Houma La. Living n Ellisville Miss.
Posts: 5,151
Likes: 0
Received 1 Like
on
1 Post
well i still think that the truck is dog rich and that is killing him on dyno if you smell gas that much at idle and you have to pump the gas to clean it out just to go then to rich
he could not put the wide band on it cause he did not have a bong for it
rich, rich, rich, rich, rich
he could not put the wide band on it cause he did not have a bong for it
rich, rich, rich, rich, rich