2005 Silverado RCSB
#1
Teching In
Thread Starter
Join Date: Jan 2009
Location: Wichita Kansas
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
2005 Silverado RCSB
Truck in sig - 2005 silverado RCSB just turnned 78K miles, power everything minus seats, power folding mirrors with turnsignals, steering wheel controls, line-x spray in bedliner, rear defrost, fog lights, silverstars in lows and fogs. DJM 4/6 control arm/flip kit drop, comes with but not installed 2 inch belltech shackles, 20inch tahoes with 60-70% 275/55/20 bridgestones out back and damn near brand new 275/45/20 goodyears up front. The check engine light is on due to there are dynomax bullets where the cat. converters should be, which pipes into 3inch magnaflow that dumps before the axle. When i did the vette servo i flushed the trans with a machine and 16 qts of new fluid and a new filter. I have all the stock suspension parts, including shocks, two extra 90% rear tires, the tow hitch and a set of 3.42 gm gears.
The bad there is some damage where (stupid me) scraped the bed side against a poll at work. It pretty much just needs just a tad more work with the body dollies and the paint ground down and a skim coat and its ready to go. The damage wasnt bad enough to go to bare metal, didnt even go threw the paint, it just dented it in.
Ok I would like to get 9500 OBO
The bad there is some damage where (stupid me) scraped the bed side against a poll at work. It pretty much just needs just a tad more work with the body dollies and the paint ground down and a skim coat and its ready to go. The damage wasnt bad enough to go to bare metal, didnt even go threw the paint, it just dented it in.
Ok I would like to get 9500 OBO
Last edited by DisOwnd; 02-04-2010 at 07:44 AM.
#3
Teching In
Thread Starter
Join Date: Jan 2009
Location: Wichita Kansas
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
some extra parts
6.2 SOLD
5.3L complete minus 1 piston and 1 rod. I have a set of dished pistons and rods out of an 05 block for this motor, so they are the beefy rods and pistons but i only have 7. Also may need a reluctor wheel. 250.00 local pick up or will meet half way depending on distance, for fuel cost.
5.3L block and crank and 6 flat top pistons and 5 rods. These are also the beefy version rod and pistons. 150.00 local pick up or will meet half way depending on distance, for fuel cost.
6.2 SOLD
5.3L complete minus 1 piston and 1 rod. I have a set of dished pistons and rods out of an 05 block for this motor, so they are the beefy rods and pistons but i only have 7. Also may need a reluctor wheel. 250.00 local pick up or will meet half way depending on distance, for fuel cost.
5.3L block and crank and 6 flat top pistons and 5 rods. These are also the beefy version rod and pistons. 150.00 local pick up or will meet half way depending on distance, for fuel cost.
Last edited by DisOwnd; 02-07-2010 at 12:41 PM.
#6
Teching In
Join Date: Jan 2010
Location: North West Arkansas
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Would you consider dealing with me in trade for an 08 Harley-Davidson Nighster?
I still owe on it but I would refinance somehow, im sure theres a way. I owe as much on the bike as you are asking for your truck, im sure we could line up the numbers somehow, anyways let me know.
I still owe on it but I would refinance somehow, im sure theres a way. I owe as much on the bike as you are asking for your truck, im sure we could line up the numbers somehow, anyways let me know.
#7
Teching In
Join Date: Jan 2010
Location: North West Arkansas
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Would you consider dealing with me in trade for an 08 Harley-Davidson Nighster?
I still owe on it but I would refinance somehow, im sure theres a way. I owe as much on the bike as you are asking for your truck, im sure we could line up the numbers somehow, anyways let me know.
I still owe on it but I would refinance somehow, im sure theres a way. I owe as much on the bike as you are asking for your truck, im sure we could line up the numbers somehow, anyways let me know.