PerformanceTrucks.net Forums
Share Your Pictures with Our Community. Upload Now
0 2024/09/02 10:02:16
Measuring the new inlet sock from Racetronix to keep everything relevant
Measuring the new inlet sock from Racetronix to keep everything relevant
0 2024/09/02 09:57:08
Measuring how far The inlet sock sits off the floor of the bucket
Measuring how far The inlet sock sits off the floor of the bucket
0 2024/09/02 09:57:04
Cut the lower part of the holder to accommodate the larger diameter bell portion of the 285 pump.
Cut the lower part of the holder to accommodate the larger diameter bell portion of the 285 pump.
0 2024/09/02 09:57:00
Drilled the holder out of the dark gray post-pump filter/regulator housing with 5/16" drill bit. ( started with smaller bits and worked up to 5/16")
Drilled the holder out of the dark gray post-pump filter/regulator housing with 5/16" drill bit. ( started with smaller bits and worked up to 5/16")
0 2024/09/02 09:56:55
Cutting floor out of pump holder
Cutting floor out of pump holder
0 2024/09/02 09:56:50
0 2024/09/02 09:56:46
F90000285 pump aka 470 LPH
F90000285 pump aka 470 LPH
0 2024/09/02 09:56:41
0 2024/09/02 09:05:01
0 2024/09/01 16:42:58
0 2024/08/31 21:35:18
All back together. I may put 100 miles on this before the TI version shows up. I'll just sell this after.
All back together. I may put 100 miles on this before the TI version shows up. I'll just sell this after.
0 2024/08/31 19:03:43
Advertisement
0 2024/08/31 19:03:39
Pump back in bucket. Unfortunately I didn't get a pic of how I secured the pump to the holder. I used 2 stainless worm-gear hose clamps after messing around with different ways until I cam up with something that allowed the pump to stay plumb.
Pump back in bucket. Unfortunately I didn't get a pic of how I secured the pump to the holder. I used 2 stainless worm-gear hose clamps after messing around with different ways until I cam up with something that allowed the pump to stay plumb.
0 2024/08/31 19:03:35
Fuel tube on pump outlet and clamp installed.
Fuel tube on pump outlet and clamp installed.
0 2024/08/31 19:03:31
Piece removed.
Piece removed.
0 2024/08/31 19:03:27
Cutting this piece out to have room for fuel tube to loop up to the pump outlet.
Cutting this piece out to have room for fuel tube to loop up to the pump outlet.
0 2024/08/31 19:03:23
After minor grinding.
After minor grinding.
0 2024/08/31 19:00:04
Marked for a little grinding.
Marked for a little grinding.
0 2024/08/31 19:00:00
I added a little clearance here.
I added a little clearance here.
0 2024/08/31 18:59:56
0 2024/08/31 18:59:52
Marked for a little grinding/clearancing.
Marked for a little grinding/clearancing.
0 2024/08/31 18:59:49
0 2024/08/31 18:59:45
Oetiker clamp installed, not the clicking of it to make sure it isn't in the way of the pump.
Oetiker clamp installed, not the clicking of it to make sure it isn't in the way of the pump.
0 2024/08/31 18:59:40
0 2024/08/31 18:50:39
0 2024/08/31 18:50:34
Stock Bosch pump outlet slides over this 7mm portion. I couldn't find 7mm fuel tube that was 10mm on the other end for pump outlet so I bought a fuel tube that's 10mm on both ends, pushed it up over the large 10mm diameter portion as seen here. Nice tight fit.
Stock Bosch pump outlet slides over this 7mm portion. I couldn't find 7mm fuel tube that was 10mm on the other end for pump outlet so I bought a fuel tube that's 10mm on both ends, pushed it up over the large 10mm diameter portion as seen here. Nice tight fit.
0 2024/08/31 18:50:30
0 2024/08/31 18:50:26
MUCH thicker.
MUCH thicker.
0 2024/08/31 18:50:21
It occurred to me that installation depth is dictated by the thickness of the filter sock on the inlet. I bought my parts from Racetronix and I believe this sock is different than the Walbro one so that's something to consider. Certainly a good thickness difference between this Racetronix one and the stock Bosch one.
It occurred to me that installation depth is dictated by the thickness of the filter sock on the inlet. I bought my parts from Racetronix and I believe this sock is different than the Walbro one so that's something to consider. Certainly a good thickness difference between this Racetronix one and the stock Bosch one.
0 2024/08/31 18:50:17
Inlet end of pump is larger diameter than stick, I relieved the bottom ring in the pump holder by cutting in 3 spots.
Inlet end of pump is larger diameter than stick, I relieved the bottom ring in the pump holder by cutting in 3 spots.
0 2024/08/31 18:45:09
Floor cut off
Floor cut off
0 2024/08/31 18:45:04
Advertisement