PerformanceTrucks.net Forums
0 2017/12/03 20:47:34
0 2017/11/30 16:54:46
0 2017/11/30 16:54:40
0 2017/11/30 16:54:29
0 2017/11/30 16:54:15
0 2017/11/30 16:54:04
0 2017/11/30 16:53:54
0 2017/11/30 16:53:46
0 2017/11/30 16:53:35
0 2017/11/30 16:45:33
0 2017/11/30 16:45:31
0 2017/11/30 16:45:29
0 2017/11/30 16:45:27
0 2017/11/30 16:45:25
0 2017/11/30 16:45:22
0 2017/11/30 16:45:19
0 2017/11/30 16:45:15
0 2017/11/28 18:52:19
It's sitting 3" lower right now then what I intend to run. Need to swap out my DJM arms for the stockers after I rebuild them with poly bushings and Moog ball joints.
It's sitting 3" lower right now then what I intend to run. Need to swap out my DJM arms for the stockers after I rebuild them with poly bushings and Moog ball joints.
0 2017/09/17 10:52:37
0 2017/09/17 10:52:36
0 2017/09/17 10:52:35
No limit straps with these coilovers.
No limit straps with these coilovers.
0 2017/09/17 10:52:34
After I move and get settled in the hood is betting replaced with a Reflexion cowl hood with paint for the hood, roof, bumper, grill and mirror caps.
After I move and get settled in the hood is betting replaced with a Reflexion cowl hood with paint for the hood, roof, bumper, grill and mirror caps.
0 2017/09/17 10:48:02
0 2017/09/17 10:48:00
0 2017/09/17 10:47:58
Intercooler fitment pics.
Intercooler fitment pics.
0 2017/09/17 10:47:57
0 2017/09/17 10:47:56
0 2017/09/15 17:28:22
0 2017/09/15 17:28:19
0 2017/09/15 17:28:16
Got my Hughes 4l80e installed along with the transfer case and cross member. All to be removed to check trans pump ears for damage since I'm a noob and installing torque converters. I think it will check good but want to be sure. When bolting the trans to block, the converter was just about flush with the flexplate so not a whole lot of pressure was pushing the converter snout on the trans pump ears but we shall see.
Got my Hughes 4l80e installed along with the transfer case and cross member. All to be removed to check trans pump ears for damage since I'm a noob and installing torque converters. I think it will check good but want to be sure. When bolting the trans to block, the converter was just about flush with the flexplate so not a whole lot of pressure was pushing the converter snout on the trans pump ears but we shall see.
0 2017/09/10 13:39:15
0 2017/09/10 13:39:11
0 2017/09/10 13:39:06
Rebuilt the np149 transfer case with all new seals, bearings, case saver and installed Time2kill's re-splinned input gear for the 4l80e. I have a ton a pics throughout the rebuild process if anyone has any questions or needs referencing.
Rebuilt the np149 transfer case with all new seals, bearings, case saver and installed Time2kill's re-splinned input gear for the 4l80e. I have a ton a pics throughout the rebuild process if anyone has any questions or needs referencing.
0 2017/09/10 13:29:18
0 2017/09/10 13:29:17
0 2017/09/10 13:29:14
All other unused sensor pins removed, Maf, knock, evap purge and evap vent. Coolant level sensor will just be grounded out.
All other unused sensor pins removed, Maf, knock, evap purge and evap vent. Coolant level sensor will just be grounded out.
0 2017/09/10 13:23:29
Speartech's 4l80e Input speed sensor harness pinned into the ECM
Speartech's 4l80e Input speed sensor harness pinned into the ECM
0 2017/09/10 13:23:26
0 2017/09/09 15:36:08
0 2017/09/09 15:35:55